MovieCut V1.2

[d-king]

MovieCut V1.2

Cekilmis Filmleri kesmek icin Plugin.

ZIP Arcivin icindeki .bz2 Dosyasini /tmp atip Blue Panelde Installation edebiliriz.

Description:
Datei nach /tmp kopieren und übers BluePanel manuell installieren.

2008-07-17
Anders Holst (aho@sics.se)


This module makes it possible to execute the cuts specified by the
Cutlist editor on DM7025, i.e. the specified sections are actually
removed from the file, saving disk space and simplifying if the movie
is to be e.g. burned to a DVD. When installed it will be accessible
from the file list menu (i.e. selecting a file in the file list and
pressing the menu button) under the name "Execute cuts...". First use
the Cutlist editor to set the appropriate cut marks. Then select
"Execute cuts..." and it will give some options for usage.

The real work is done by the program "mcut". It was inspired and
guided by the similar package "moviecutter" bu Georges. However, you
need not wait over the night but it can run in the background as you
keep watching on your dreambox, and a typical movie takes about 15-20
minutes to process. The program "mcut" can also be called directly
from a shell. With no arguments it will give a brief description of
the options.


News since version 1.1

* Nothing really is supposed to have changed functionally. However,
the plugin is updated to the skin changes of 2008-04-14, and the
location changes of 2008-06-28, and it uses eConsoleAppContainer
instead of spawnv/waitpid to launch "mcut".


News since version 1.0

* Cutting is still in the background, but now a notification will pop
up either when cutting is successfully finished, or with a suitable
error message if cutting fails.

* The cutting can now be done quite exact: If all cut marks are placed
at GOP boundaries (singlestep GOPs by pausing and pressing either
"rewind" or with the appropriate settings "pause"), then the
retained part will start with the same frame you were at when you
placed the IN cut, and it will stop just a few frames before
(typically 3 frames before - I can't easily get rid of this) the one
where you placed the OUT cut. Note however that due to a bug in
enigma2 (still there 2008-02-28) the CutListEditor will set the mark
at the right place, but when revisiting the mark you will end up one
GOP later. Trust the original mark position, not where it seems to
be when jumping to it.

* There are no flickering between cuts any more! There is a small (3
frames long) pause before the next cut starts, but all flickering
and squares seem to be gone. I believe this is as good as it can get
without remuxing.


Caveats

* Since some time in the spring 2008 there seems to be a change/bug in
enigma2 that makes the elapsed time calculation somewhat offset
compared to earlier. This appears such that cut marks placed with
earlier versions appears to have drifted when watched in the new
version of enigma2. MovieCut is still callibrated to the earlier
calculation, and may thus also place the cuts somewhat offset from
the intended places. Always cut to a new file and check the result
to be on the safe side!

* The manual specification of cuts in the "advanced cut parameter"
dialogue is as awkward as before to specify with the remote control:
"0" is mapped to ".","0", and ":" since this was most
straightforward to implement using existing python code. Also note
that the cuts are given in pairs of *included* sections, not
*excluded* as in the cutlist editor (i.e. there is first an IN time,
followed by OUT, and so on).

* Although the flickering between cuts may be gone when looking at the
movie on the dreambox, there is no guarantee that they are gone when
trying to convert it to mpeg for burning to DVD or similar. It is
not even guaranteed that they can be easily converted at all - at
least one program is reported to fail to continue after the first
cut.


Disclaimer

I have really tried to be careful and make it reasonably "safe": It
checks for errors during the process and will abort in a controlled
way if it happens; If "-r"="replace" is specified, it will not remove
any files until the whole cutting is successfully done; if "-r" is not
given it will not overwrite any existing file with the same name as the
destination; if no cuts are specified nothing will be done; etc.

However, all use will be on your own risk. I will not take
responsibility for any damage or loss of movies or other files due to
either bugs in the program or uncareful use.

[Değerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanız gerekiyorÜye olmak icin burayı tıklayınız]

[d-king]

Almanca versionu.

MovieCut V1.2 German

10.08.2008Code:
Description:
Datei nach /tmp kopieren und übers BluePanel manuell installieren.

MovieCut von Anders Holst (aho@sics.se)
Eingedeutscht von Swiss-MAD & DLH007

MovieCut von Anders Holst
* It is adapted to the skin changes of 2008-04-14.
* It includes the possibility to cut into another location, using the location changes of 2008-06-28 (in the 2.5 branch of Enigma2, which means that this branch is required).
* It uses eConsoleAppContainer instead of spawnv/waitpid to launch "mcut".

[Değerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanız gerekiyorÜye olmak icin burayı tıklayınız]