Dreamboka hiçbirşekilde bağlanamıyorum. İmaj atamıyorum.

Arkadaşlar, bu sefer sorunu çözemeyeceğim gibi. Sabahtan bu yana çok bunaldım.

İnşallah üstadlar yardımlarını esirgemez.

Dreambox DM525 SIM 2.30 klon cihazım var. Dupengda üretimi yani Çin model.

Cihazımda OpenATV 6.0 imaj yüklü idi. Yeni OpenATV 6.2 imaj ve farklı imajlar çıkmış. Onları denemek istedim.

Maalesef cihaz çöktü sanırım.

Kırmızı ışıkta takılı kaldı. hiçbir şekilde bağlantı kuramıyorum.
IP almıyor. Birçok defa ön tarafa basılı tutarak açmaya çalıştım ancak direk kırmızı ışığa geçiyor.
Telnet bağlanmıyor.
DreamUP ile de bağlantı kuramıyorum.
Driverı yükledim, Service kısmından USB ile bilgisayara bağlıyorum, com port seçiliyor ancak fişi takınca bir hareket olmuyor.
Modemden İnternet alan cihazlarımı kontrol ettiğimde dreambox görünmüyor.

JapharFlasher ı da denedim ama oda bağlanmıyor.

YAPABİLECEĞİM BAŞKA BİR ALTERNATİF VAR MI ARKADAŞLAR.?


Putty ile bağlantı kurmaya çalıştım, onu da beceremedim.

putty i de open deyince aşağıdaki döküm çıkıyor.

Dreambox DM520

M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@

BCM973625A0 CFE v15.3, Endian Mode: Little
Build Date: Fri Aug 19 11:48:16 2016 (Jann@Cynric)
Copyright (C) Broadcom Corporation.

CI box detected
card if inited
Enabling NAND flash at CS2: HY27UF084G(DEVICE ID=0xADDC14A5), ECC Level=4, Spare Area Size=16
MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256

CPU speed: 751MHz
DDR Frequency: 1061 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 16MB
RTS VERSION: rts_hevc10_1067
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1

DM init finalization
yxml: processing file of 131072 bytes... succeeded!
no file loaded, create xml restoring default xml
loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1
[1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options
[2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options
[3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M con sole=ttyS0,1000000 root=/dev/nfs ip=dhcp
added 3 sources to autoboot list
init fp
Initializing USB.

CFE initialized.
found card in unknown state
ca valid!



***** DREAMBOX SSBL *****

Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 5 00ms to cancel
Proceeding with autoboot.. You can try aborting with Ctrl+C

*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)

Ethernet link is up: 100 Mbps Full-Duplex
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:
Loading: 0x80001000/8460480 0x808128c0/258288 Entry address is 0x80675a00
Closing network eth0
Starting program at 0x80675a00

[ 0.250000] console [ttyS0] enabled, bootconsole disabled
[ 0.250000] console [ttyS0] enabled, bootconsole disabled
[ 0.254000] loop: module loaded
[ 0.255000] brcmstb_nand: NAND controller driver is loaded
[ 0.377000] bcmgenet: configuring instance #0 for internal PHY
[ 0.397000] bcmgenet bcmgenet.0: (unregistered net_device): link down
[ 0.398000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.399000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.399000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numbe r 1
[ 0.431000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
[ 0.437000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.438000] hub 1-0:1.0: USB hub found
[ 0.438000] hub 1-0:1.0: 2 ports detected
[ 0.439000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.440000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.440000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numbe r 2
[ 0.441000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
[ 0.507000] hub 2-0:1.0: USB hub found
[ 0.508000] hub 2-0:1.0: 2 ports detected
[ 0.508000] Initializing USB Mass Storage driver...
[ 0.509000] usbcore: registered new interface driver usb-storage
[ 0.510000] USB Mass Storage support registered.
[ 0.510000] i2c /dev entries driver
[ 0.511000] lirc_dev: IR Remote Control driver registered, major 253
[ 0.511000] usbcore: registered new interface driver btusb
[ 0.513000] TCP: cubic registered
[ 0.513000] NET: Registered protocol family 10
[ 0.515000] NET: Registered protocol family 17
[ 0.515000] Bluetooth: RFCOMM TTY layer initialized
[ 0.516000] Bluetooth: RFCOMM socket layer initialized
[ 0.517000] Bluetooth: RFCOMM ver 1.11
[ 0.517000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 0.518000] Bluetooth: BNEP filters: protocol multicast
[ 0.518000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.519000] L2TP core driver, V2.0
[ 0.520000] Registering the dns_resolver key type
[ 0.520000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
[ 0.522000] EBI CS2: setting up NAND flash (primary)
[ 0.523000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512 MiB 3,3V 8-bit)
[ 0.524000] brcmnand brcmnand.0: 512MiB total, 256KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
[ 0.524000]
[ 0.526000] Bad block table found at page 262016, version 0x01
[ 0.527000] Bad block table found at page 261888, version 0x01
[ 0.528000] nand_read_bbt: bad block at 0x000011900000
[ 0.529000] nand_read_bbt: bad block at 0x000011940000
[ 0.529000] nand_read_bbt: bad block at 0x00001d380000
[ 0.530000] nand_read_bbt: bad block at 0x00001d3c0000
[ 0.531000] Creating 3 MTD partitions on "brcmnand.0":
[ 0.532000] 0x000000000000-0x00001f500000 : "rootfs"
[ 0.534000] 0x000000000000-0x000020000000 : "entire_device"
[ 0.535000] 0x00001f500000-0x00001fa00000 : "kernel"
[ 0.537000] EBI CS0: setting up SPI flash
[ 0.537000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
[ 0.538000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated
[ 0.539000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv
[ 0.540000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.542000] UBI: attaching mtd0 to ubi0
[ 0.543000] UBI: physical eraseblock size: 262144 bytes (256 KiB)
[ 0.543000] UBI: logical eraseblock size: 258048 bytes
[ 0.544000] UBI: smallest flash I/O unit: 2048
[ 0.544000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.545000] UBI: data offset: 4096
[ 2.160000] UBI: max. sequence number: 10288
[ 2.174000] UBI: attached mtd0 to ubi0
[ 2.175000] UBI: MTD device name: "rootfs"
[ 2.175000] UBI: MTD device size: 501 MiB
[ 2.176000] UBI: number of good PEBs: 2000
[ 2.176000] UBI: number of bad PEBs: 4
[ 2.177000] UBI: number of corrupted PEBs: 0
[ 2.177000] UBI: max. allowed volumes: 128
[ 2.178000] UBI: wear-leveling threshold: 4096
[ 2.178000] UBI: number of internal volumes: 1
[ 2.179000] UBI: number of user volumes: 1
[ 2.179000] UBI: available PEBs: 0
[ 2.180000] UBI: total number of reserved PEBs: 2000
[ 2.181000] UBI: number of PEBs reserved for bad PEB handling: 20
[ 2.181000] UBI: max/mean erase counter: 16/6
[ 2.182000] UBI: image sequence number: -1125229945
[ 2.182000] UBI: background thread "ubi_bgt0d" started, PID 55
[ 2.184000] ALSA device list:
[ 2.185000] No soundcards found.

[ 2.288000] UBIFS: recovery needed
[ 2.542000] UBIFS: recovery completed
[ 2.542000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs"
[ 2.543000] UBIFS: file system size: 507322368 bytes (495432 KiB, 483 MiB, 1966 LEBs)
[ 2.544000] UBIFS: journal size: 9420800 bytes (9200 KiB, 8 MiB, 37 LEB s)
[ 2.545000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 2.546000] UBIFS: default compressor: lzo
[ 2.546000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.550000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 2.552000] devtmpfs: mounted
[ 2.568000] Kernel panic - not syncing: No init found. Try passing init= opt ion to kernel. See Linux Documentation/init.txt for guidance.
[ 2.569000] Rebooting in 180 seconds..

kardes tam yardimci olurmu bilmiyorum senin cihazin IP adresini biliyorsan putty ile baglaniyorsan eger putty ile baglan asagidaki komutu ver putty ile cihaz kapanip acilir ve senin browsere cihazin IP ver ve imageni yükle baska care aklima gelmedi kolayliklar .

to-the-rescue

puty ile BIOS ayar kısmına girdim.
orda Network ayarlarını yaptığımda, modem arayüzünde cihazın internete bağlandığını görüyorum.
ancak ordaki IP ye Telnet ile bağlanmaya çalıştığımda , bağlanmıyor. explorrer a IP yi yazdığımda girmiyor.
Restart yapınca da bağlantı gidiyor.

Sizin bu dediğiniz kodu puty de nereye yazacağım. şuan BIOS ayar kısmındayım. bu kodu yazacak neresi var?

Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.

diğerlerinde problem yok gibi.

Bunu nasıl düzeltebiliriz?

2.287000] UBIFS: recovery needed
[ 2.541000] UBIFS: recovery completed
[ 2.542000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs"
[ 2.543000] UBIFS: file system size: 507322368 bytes (495432 KiB, 483 MiB, 1966 LEBs)
[ 2.544000] UBIFS: journal size: 9420800 bytes (9200 KiB, 8 MiB, 37 LEBs)
[ 2.544000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 2.545000] UBIFS: default compressor: lzo
[ 2.546000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.550000] VFS: Mounted root (ubifs filesystem) on device 0:12.
[ 2.552000] devtmpfs: mounted
[ 2.567000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.

Ustadım birde aşağıdaki konuya bak belki işine yarar umarım sorunu çözersin kolay gelsin.
[Değerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanız gerekiyorÜye olmak icin burayı tıklayınız]

Maalesef, hiçbiri işe yaramadı.
İstanbul Avrupa yakasında iyi bir tamirci bildiği olan var mıdır?
Cihazı nereye götür meliyim?


HUAWEI NXT-L29 cihazımdan Tapatalk kullanılarak gönderildi