turk-dreamworld.com Sitesine Hoþgeldiniz.


2 sonuçtan 1 ile 2 arasý
  1. #1
    Junior Member talhakrgzoglu - ait Kullanýcý Resmi (Avatar)
    Üyelik tarihi
    Oct 2017
    Mesajlar
    2
    Total 'Thanks' Received by This User :
    0 Bu Konu icin
    4 Toplam

    Exclamation Dreambox 900 uhd kýrmýzý ýþýk

    Attýðým yazýlým sonrasý cihazý reboot ettikten sonra kýrmýzý ýþýk sabit kaldý hiç görüntü gelmiyor ne yapabilirim?
    Putty ile boot menüsüne giremiyorum aþaðýdaki þekilde çýkýyor

    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON

    single board
    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
    MEMSYS-STD
    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
    MCB: FLEX
    AVS start:status=000000ff
    STB: Current voltage=00000381(897)
    temperature=00009bf0(39920)
    PV=00000344(836)
    MV=00000381(897)
    AVS FW rev=30333278 [0.3.2.x]
    OK
    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
    Sdram Scramble OTP = 0x00000001
    Sdram Scramble OK
    select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
    BFW load mode OTP = 0x0000000f
    bfw_hash_locked = 0x00000000
    BFW key3 OK, BFW load OK
    BFW v2.1.0
    COPY CODE... DONE
    MICH: disable success
    SSBL
    PINMUX
    CACHE FLUSH OK
    MMU ON
    CACHE FLUSH OK
    _fbss 07080cd0
    _ebss 0713dd70
    _end 0713dd90
    HEAP @ 07200000
    STACK @ 09300000
    ARCH: CONFIG OK
    CLR BSS 07080cd0 to 0713dd70 OK
    CLR SRAM OK
    CACHE FLUSH OK
    CPU CLKSET OK
    GO!

    ,/
    ,'/___, BOLT v1.18 v1.18 LOCAL BUILD
    .'__ ,' (2016-12-01 1631 cynric@cynric-VirtualBox)
    /,' Copyright (C) 2016 Broadcom
    /'

    Board: BCM97252SSFF
    SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
    otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
    otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
    CPU: 2x B15 [420f00f3] 1719 MHz
    SCB: 432 MHz
    DDR0 @ 1067MHz, DDR1 @ 1067MHz
    RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
    CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
    CS1: NAND: unrecognized ID: 0xffff 0xffffffff
    RTS0: 0x1101004, 256 clients, ok
    RTS1: 0x1181004, 256 clients, ok
    BOX MODE: 5
    card if inited
    set pwm to 0/255
    disp id 5420
    load image
    AVS: park check
    AVS: temperature monitoring enabled
    AVS: STB: V=0.897V, T=+41.381C, PV=0.836V, MV=0.897V, FW=30333278 [0.3.2.x]
    USB otp=00000040
    USB @ 0xf0470200: IPP is active low, IOC is negative polarity
    init fp
    found card in unknown state
    ca valid!
    set pwm to 200/255
    Normal bootup
    Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Optionsnull)
    Reading 4248920 bytes from zImage...........
    Starting program at 0x8000 (DTB @ 0x7728000)

    32 bit boot...
    Uncompressing Linux... done, booting the kernel.
    [ 0.000000] Booting Linux on physical CPU 0x0
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.14-1.17-dm900 (dm900@opendreambox.org) (gcc version 5.3.0 (GCC) ) #1 SMP Tue Oct 17 0857 UTC 2017
    [ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
    [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [ 0.000000] Machine model: BCM97252SSFF
    [ 0.000000] moving dtb from 0x0000000007728000 to 0x0000000000835e70
    [ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000
    [ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000
    [ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
    [ 0.000000] Memory policy: Data cache writealloc
    [ 0.000000] MCP: Enabling write pairing
    [ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s8384 r8192 d16192 u32768
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
    [ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M
    [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [ 0.000000] Memory: 1006912K/2097152K available (6114K kernel code, 214K rwdata, 1584K rodata, 244K init, 208K bss, 1073856K reserved, 16384K cma-reserved, 786428K highmem)
    [ 0.000000] Virtual kernel memory layout:
    [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
    [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
    [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
    [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
    [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
    [ 0.000000] .text : 0xc0008000 - 0xc078ccec (7700 kB)
    [ 0.000000] .init : 0xc078d000 - 0xc07ca0c0 ( 245 kB)
    [ 0.000000] .data : 0xc07cc000 - 0xc0801b20 ( 215 kB)
    [ 0.000000] .bss : 0xc0801b28 - 0xc0835e70 ( 209 kB)
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] Additional per-CPU info printed with stalls.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
    [ 0.000000] NR_IRQS:16 nr_irqs:16 16
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
    [ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
    [ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
    [ 0.000009] Switching to timer-based delay loop
    [ 0.000233] Console: colour dummy device 80x30
    [ 0.000255] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
    [ 0.000263] pid_max: default: 32768 minimum: 301
    [ 0.000358] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000364] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.005856] Initializing cgroup subsys devices
    [ 0.005869] Initializing cgroup subsys freezer
    [ 0.005876] Initializing cgroup subsys net_cls
    [ 0.005905] CPU: Testing write buffer coherency: ok
    [ 0.006124] CPU0: update cpu_power 1024
    [ 0.006129] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [ 0.006178] Setting up static identity map for 0x5d5ab8 - 0x5d5b10
    [ 0.007387] CPU1: Booted secondary processor
    [ 0.007406] CPU1: update cpu_power 1024
    [ 0.007409] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [ 0.007477] Brought up 2 CPUs
    [ 0.007487] SMP: Total of 2 processors activated (108.00 BogoMIPS).
    [ 0.007492] CPU: All CPU(s) started in SVC mode.
    [ 0.007875] devtmpfs: initialized
    [ 0.011498] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
    [ 0.012052] regulator-dummy: no parameters
    [ 0.012248] NET: Registered protocol family 16
    [ 0.013156] DMA: preallocated 2048 KiB pool for atomic coherent allocations
    [ 0.013342] cpuidle: using governor ladder
    [ 0.013347] cpuidle: using governor menu
    [ 0.014486] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
    [ 0.014570] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
    [ 0.016276] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
    [ 0.016350] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
    [ 0.016417] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
    [ 0.016481] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
    [ 0.016543] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
    [ 0.016610] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
    [ 0.016674] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
    [ 0.016738] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
    [ 0.016800] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
    [ 0.016869] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
    [ 0.016934] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
    [ 0.016998] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
    [ 0.017061] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
    [ 0.017142] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
    [ 0.017445] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
    [ 0.017677] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
    [ 0.022012] bio: create slab <bio-0> at 0
    [ 0.022320] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
    [ 0.022346] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
    [ 0.022374] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
    [ 0.022386] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
    [ 0.022731] SCSI subsystem initialized
    [ 0.022941] usbcore: registered new interface driver usbfs
    [ 0.022971] usbcore: registered new interface driver hub
    [ 0.023029] usbcore: registered new device driver usb
    [ 0.023048] media: Linux media interface: v0.10
    [ 0.023073] Linux video capture interface: v2.00
    [ 0.023111] pps_core: LinuxPPS API ver. 1 registered
    [ 0.023115] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [ 0.023125] PTP clock support registered
    [ 0.023355] Advanced Linux Sound Architecture Driver Initialized.
    [ 0.023638] Bluetooth: Core ver 2.18
    [ 0.023651] NET: Registered protocol family 31
    [ 0.023654] Bluetooth: HCI device and connection manager initialized
    [ 0.023663] Bluetooth: HCI socket layer initialized
    [ 0.023670] Bluetooth: L2CAP socket layer initialized
    [ 0.023676] Bluetooth: SCO socket layer initialized
    [ 0.024073] Switched to clocksource arch_sys_counter
    [ 0.024085] cfg80211: Calling CRDA to update world regulatory domain
    [ 0.028430] thermal thermal_zone0: failed to read out thermal zone 0
    [ 0.028517] NET: Registered protocol family 2
    [ 0.028916] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.028932] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    [ 0.028953] TCP: Hash tables configured (established 2048 bind 2048)
    [ 0.028987] TCP: reno registered
    [ 0.028993] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.029004] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.029140] NET: Registered protocol family 1
    [ 0.029362] RPC: Registered named UNIX socket transport module.
    [ 0.029368] RPC: Registered udp transport module.
    [ 0.029371] RPC: Registered tcp transport module.
    [ 0.029374] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.029976] futex hash table entries: 512 (order: 3, 32768 bytes)
    [ 0.030320] bounce pool size: 64 pages
    [ 0.030847] NFS: Registering the id_resolver key type
    [ 0.030873] Key type id_resolver registered
    [ 0.030877] Key type id_legacy registered
    [ 0.030888] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    [ 0.031024] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
    [ 0.031341] msgmni has been set to 462
    [ 0.032094] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
    [ 0.032101] io scheduler noop registered
    [ 0.032118] io scheduler cfq registered (default)
    [ 0.032339] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
    [ 0.032622] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
    [ 0.098358] brcmstb_memc f1102000.memc-ddr: registered
    [ 0.098383] brcmstb_memc f1182000.memc-ddr: registered
    [ 0.098578] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.099394] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
    [ 0.196020] console [ttyS0] enabled
    [ 0.197274] loop: module loaded
    [ 0.197919] ahci brcmstb-ahci.0: can't get clock
    [ 0.198539] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
    [ 0.210088] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
    [ 0.211083] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
    [ 0.213724] scsi0 : ahci_platform
    [ 0.214357] scsi1 : ahci_platform
    [ 0.214861] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
    [ 0.215778] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
    [ 0.217212] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
    [ 0.217978] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
    [ 0.219122] m25p80 spi32766.0: found mx25l25635e, expected m25p80
    [ 0.219828] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
    [ 0.220562] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
    [ 0.221210] 5 ofpart partitions found on MTD device spi32766.0
    [ 0.221880] Creating 5 MTD partitions on "spi32766.0":
    [ 0.222479] 0x000000000000-0x000000200000 : "flash0.bolt"
    [ 0.223580] 0x000000200000-0x000000220000 : "flash0.nvram"
    [ 0.224620] 0x000000220000-0x000000240000 : "flash0.devtree"
    [ 0.225678] 0x000000240000-0x000001000000 : "flash0.recovery"
    [ 0.226749] 0x000000000000-0x000002000000 : "flash0"
    [ 0.228023] libphy: Fixed MDIO Bus: probed
    [ 0.228626] tun: Universal TUN/TAP device driver, 1.6
    [ 0.229215] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [ 0.230253] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
    [ 0.244079] libphy: bcmgenet MII bus: probed
    [ 0.264956] xhci-brcm: xHCI BRCM driver
    [ 0.265479] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
    [ 0.266150] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
    [ 0.267331] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
    [ 0.268174] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.268953] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.269789] usb usb1: Product: xHCI Host Controller
    [ 0.270355] usb usb1: Manufacturer: Linux 3.14-1.17-dm900 xhci-hcd
    [ 0.271070] usb usb1: SerialNumber: f0471000.xhci_v2
    [ 0.271957] hub 1-0:1.0: USB hub found
    [ 0.272421] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
    [ 0.273352] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
    [ 0.274012] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
    [ 0.275033] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
    [ 0.275827] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.276666] usb usb2: Product: xHCI Host Controller
    [ 0.277235] usb usb2: Manufacturer: Linux 3.14-1.17-dm900 xhci-hcd
    [ 0.277944] usb usb2: SerialNumber: f0471000.xhci_v2
    [ 0.278789] hub 2-0:1.0: USB hub found
    [ 0.279250] hub 2-0:1.0: 2 ports detected
    [ 0.280018] ehci-brcm: EHCI BRCM driver
    [ 0.280546] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
    [ 0.281214] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
    [ 0.292228] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
    [ 0.298084] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
    [ 0.298891] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.299679] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.300513] usb usb3: Product: EHCI Host Controller
    [ 0.301081] usb usb3: Manufacturer: Linux 3.14-1.17-dm900 ehci_hcd
    [ 0.301790] usb usb3: SerialNumber: f0470300.ehci_v2
    [ 0.302637] hub 3-0:1.0: USB hub found
    [ 0.303096] hub 3-0:1.0: 1 port detected
    [ 0.303734] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
    [ 0.304403] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
    [ 0.315397] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
    [ 0.322081] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
    [ 0.322884] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.323672] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.324506] usb usb4: Product: EHCI Host Controller
    [ 0.325073] usb usb4: Manufacturer: Linux 3.14-1.17-dm900 ehci_hcd
    [ 0.325782] usb usb4: SerialNumber: f0470500.ehci_v2
    [ 0.326091] ata1: SATA link down (SStatus 0 SControl 300)
    [ 0.327245] hub 4-0:1.0: USB hub found
    [ 0.327698] hub 4-0:1.0: 1 port detected
    [ 0.328397] ohci-brcm: OHCI BRCM driver
    [ 0.328891] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
    [ 0.329564] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
    [ 0.330488] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
    [ 0.386191] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
    [ 0.386971] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.387806] usb usb5: Product: BRCM OHCI controller
    [ 0.388374] usb usb5: Manufacturer: Linux 3.14-1.17-dm900 ohci_hcd
    [ 0.389089] usb usb5: SerialNumber: f0470400.ohci_v2
    [ 0.389938] hub 5-0:1.0: USB hub found
    [ 0.390414] hub 5-0:1.0: 1 port detected
    [ 0.391085] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
    [ 0.391748] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
    [ 0.392671] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
    [ 0.438082] ata2: SATA link down (SStatus 0 SControl 300)
    [ 0.448180] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
    [ 0.448960] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.449796] usb usb6: Product: BRCM OHCI controller
    [ 0.450363] usb usb6: Manufacturer: Linux 3.14-1.17-dm900 ohci_hcd
    [ 0.451079] usb usb6: SerialNumber: f0470600.ohci_v2
    [ 0.451906] hub 6-0:1.0: USB hub found
    [ 0.452375] hub 6-0:1.0: 1 port detected
    [ 0.453073] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.453823] ehci-pci: EHCI PCI platform driver
    [ 0.454380] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.455100] ohci-pci: OHCI PCI platform driver
    [ 0.455725] usbcore: registered new interface driver usb-storage
    [ 0.456428] i2c /dev entries driver
    [ 0.456883] lirc_dev: IR Remote Control driver registered, major 250
    [ 0.457927] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
    [ 0.458901] usbcore: registered new interface driver btusb
    [ 0.459594] cpufreq_cpu0: failed to get cpu0 regulator: -19
    [ 0.460410] brcmstb-cpufreq: probe of f03e257c.cpu-clk-div failed with error -17
    [ 0.461337] sdhci: Secure Digital Host Controller Interface driver
    [ 0.462044] sdhci: Copyright(c) Pierre Ossman
    [ 0.462552] sdhci-pltfm: SDHCI platform and OF driver helper
    [ 0.464305] mmc0: no vqmmc regulator found
    [ 0.464779] mmc0: no vmmc regulator found
    [ 0.495083] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
    [ 0.496991] mmc1: no vqmmc regulator found
    [ 0.497470] mmc1: no vmmc regulator found
    [ 0.528078] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
    [ 0.529023] hidraw: raw HID events driver (C) Jiri Kosina
    [ 0.529737] usbcore: registered new interface driver usbhid
    [ 0.530384] usbhid: USB HID core driver
    [ 0.532819] TCP: cubic registered
    [ 0.533820] NET: Registered protocol family 10
    [ 0.534813] NET: Registered protocol family 17
    [ 0.535564] Bluetooth: RFCOMM TTY layer initialized
    [ 0.536147] Bluetooth: RFCOMM socket layer initialized
    [ 0.536736] Bluetooth: RFCOMM ver 1.11
    [ 0.537176] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 0.537786] Bluetooth: BNEP filters: protocol multicast
    [ 0.538395] Bluetooth: BNEP socket layer initialized
    [ 0.538965] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [ 0.539654] Bluetooth: HIDP socket layer initialized
    [ 0.540275] l2tp_core: L2TP core driver, V2.0
    [ 0.540798] Key type dns_resolver registered
    [ 0.541367] Registering SWP/SWPB emulation handler
    [ 0.542192] regulator-dummy: disabling
    [ 0.542825] ALSA device list:
    [ 0.543189] No soundcards found.
    [ 0.543804] Waiting for root device /dev/mmcblk0p2...
    [ 0.595724] mmc1: BKOPS_EN bit is not set
    [ 0.602427] mmc1: new high speed MMC card at address 0001
    [ 0.603251] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
    [ 0.603854] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
    [ 0.604652] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
    [ 0.605413] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
    [ 0.609142] mmcblk0: p1 p2 p3
    [ 0.611681] mmcblk0boot1: unknown partition table
    [ 0.612711] mmcblk0boot0: unknown partition table
    [ 0.650269] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
    [ 0.651232] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
    [ 0.652435] devtmpfs: error mounting -2
    [ 0.652922] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
    [ 0.654425] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14-1.17-dm900 #1
    [ 0.655214] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x10/0x14)
    [ 0.656107] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c)
    [ 0.656939] [<c05d0408>] (dump_stack) from [<c05cf770>] (panic+0xa0/0x1f0)
    [ 0.657730] [<c05cf770>] (panic) from [<c05cd564>] (cpu_die+0x0/0x90)
    [ 0.658470] [<c05cd564>] (cpu_die) from [<00000000>] ( (null))
    [ 0.659157] CPU0: stopping
    [ 0.659473] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14-1.17-dm900 #1
    [ 0.660248] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x10/0x14)
    [ 0.661138] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c)
    [ 0.661968] [<c05d0408>] (dump_stack) from [<c00140d4>] (handle_IPI+0x164/0x198)
    [ 0.662818] [<c00140d4>] (handle_IPI) from [<c00085cc>] (gic_handle_irq+0x58/0x5c)
    [ 0.663688] [<c00085cc>] (gic_handle_irq) from [<c0011dc0>] (__irq_svc+0x40/0x50)
    [ 0.664546] Exception stack(0xc07cdf60 to 0xc07cdfa8)
    [ 0.665127] df60: ffffffed 0d7f8000 c07d54c8 00000000 c07cc030 c07d4420 c07d449c c05d788c
    [ 0.666065] df80: c0801961 c0801961 c07cc000 00000000 00000000 c07cdfa8 c000efb0 c000efa8
    [ 0.667000] dfa0: 60000113 ffffffff
    [ 0.667407] [<c0011dc0>] (__irq_svc) from [<c000efa8>] (arch_cpu_idle+0x2c/0x38)
    [ 0.668260] [<c000efa8>] (arch_cpu_idle) from [<c00638f8>] (cpu_startup_entry+0x100/0x144)
    [ 0.669214] [<c00638f8>] (cpu_startup_entry) from [<c078dbf0>] (start_kernel+0x414/0x420)

    PROBLEM NE OLABÝLÝR NE YPMAMIZ LAZIM?
    AlýntýAlýntý

  2. #2
    Senior Member atlas - ait Kullanýcý Resmi (Avatar)
    Üyelik tarihi
    Aug 2009
    Bulunduðu yer
    avrupa
    Mesajlar
    169
    Total 'Thanks' Received by This User :
    2 Bu Konu icin
    101 Toplam

    Standart Cevap: Dreambox 900 uhd kýrmýzý ýþýk

    Alýntý talhakrgzoglu Nickli Üyeden Alýntý [Deðerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanýz gerekiyorÜye olmak icin burayý týklayýnýz]
    Attýðým yazýlým sonrasý cihazý reboot ettikten sonra kýrmýzý ýþýk sabit kaldý hiç görüntü gelmiyor ne yapabilirim?
    Putty ile boot menüsüne giremiyorum aþaðýdaki þekilde çýkýyor

    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON

    single board
    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
    MEMSYS-STD
    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
    MCB: FLEX
    AVS start:status=000000ff
    STB: Current voltage=00000381(897)
    temperature=00009bf0(39920)
    PV=00000344(836)
    MV=00000381(897)
    AVS FW rev=30333278 [0.3.2.x]
    OK
    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
    Sdram Scramble OTP = 0x00000001
    Sdram Scramble OK
    select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
    BFW load mode OTP = 0x0000000f
    bfw_hash_locked = 0x00000000
    BFW key3 OK, BFW load OK
    BFW v2.1.0
    COPY CODE... DONE
    MICH: disable success
    SSBL
    PINMUX
    CACHE FLUSH OK
    MMU ON
    CACHE FLUSH OK
    _fbss 07080cd0
    _ebss 0713dd70
    _end 0713dd90
    HEAP @ 07200000
    STACK @ 09300000
    ARCH: CONFIG OK
    CLR BSS 07080cd0 to 0713dd70 OK
    CLR SRAM OK
    CACHE FLUSH OK
    CPU CLKSET OK
    GO!

    ,/
    ,'/___, BOLT v1.18 v1.18 LOCAL BUILD
    .'__ ,' (2016-12-01 1631 cynric@cynric-VirtualBox)
    /,' Copyright (C) 2016 Broadcom
    /'

    Board: BCM97252SSFF
    SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
    otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
    otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
    CPU: 2x B15 [420f00f3] 1719 MHz
    SCB: 432 MHz
    DDR0 @ 1067MHz, DDR1 @ 1067MHz
    RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
    CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
    CS1: NAND: unrecognized ID: 0xffff 0xffffffff
    RTS0: 0x1101004, 256 clients, ok
    RTS1: 0x1181004, 256 clients, ok
    BOX MODE: 5
    card if inited
    set pwm to 0/255
    disp id 5420
    load image
    AVS: park check
    AVS: temperature monitoring enabled
    AVS: STB: V=0.897V, T=+41.381C, PV=0.836V, MV=0.897V, FW=30333278 [0.3.2.x]
    USB otp=00000040
    USB @ 0xf0470200: IPP is active low, IOC is negative polarity
    init fp
    found card in unknown state
    ca valid!
    set pwm to 200/255
    Normal bootup
    Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Optionsnull)
    Reading 4248920 bytes from zImage...........
    Starting program at 0x8000 (DTB @ 0x7728000)

    32 bit boot...
    Uncompressing Linux... done, booting the kernel.
    [ 0.000000] Booting Linux on physical CPU 0x0
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.14-1.17-dm900 (dm900@opendreambox.org) (gcc version 5.3.0 (GCC) ) #1 SMP Tue Oct 17 0857 UTC 2017
    [ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
    [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [ 0.000000] Machine model: BCM97252SSFF
    [ 0.000000] moving dtb from 0x0000000007728000 to 0x0000000000835e70
    [ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000
    [ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000
    [ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
    [ 0.000000] Memory policy: Data cache writealloc
    [ 0.000000] MCP: Enabling write pairing
    [ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s8384 r8192 d16192 u32768
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
    [ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M
    [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [ 0.000000] Memory: 1006912K/2097152K available (6114K kernel code, 214K rwdata, 1584K rodata, 244K init, 208K bss, 1073856K reserved, 16384K cma-reserved, 786428K highmem)
    [ 0.000000] Virtual kernel memory layout:
    [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
    [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
    [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
    [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
    [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
    [ 0.000000] .text : 0xc0008000 - 0xc078ccec (7700 kB)
    [ 0.000000] .init : 0xc078d000 - 0xc07ca0c0 ( 245 kB)
    [ 0.000000] .data : 0xc07cc000 - 0xc0801b20 ( 215 kB)
    [ 0.000000] .bss : 0xc0801b28 - 0xc0835e70 ( 209 kB)
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] Additional per-CPU info printed with stalls.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
    [ 0.000000] NR_IRQS:16 nr_irqs:16 16
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
    [ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
    [ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
    [ 0.000009] Switching to timer-based delay loop
    [ 0.000233] Console: colour dummy device 80x30
    [ 0.000255] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
    [ 0.000263] pid_max: default: 32768 minimum: 301
    [ 0.000358] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000364] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.005856] Initializing cgroup subsys devices
    [ 0.005869] Initializing cgroup subsys freezer
    [ 0.005876] Initializing cgroup subsys net_cls
    [ 0.005905] CPU: Testing write buffer coherency: ok
    [ 0.006124] CPU0: update cpu_power 1024
    [ 0.006129] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [ 0.006178] Setting up static identity map for 0x5d5ab8 - 0x5d5b10
    [ 0.007387] CPU1: Booted secondary processor
    [ 0.007406] CPU1: update cpu_power 1024
    [ 0.007409] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [ 0.007477] Brought up 2 CPUs
    [ 0.007487] SMP: Total of 2 processors activated (108.00 BogoMIPS).
    [ 0.007492] CPU: All CPU(s) started in SVC mode.
    [ 0.007875] devtmpfs: initialized
    [ 0.011498] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
    [ 0.012052] regulator-dummy: no parameters
    [ 0.012248] NET: Registered protocol family 16
    [ 0.013156] DMA: preallocated 2048 KiB pool for atomic coherent allocations
    [ 0.013342] cpuidle: using governor ladder
    [ 0.013347] cpuidle: using governor menu
    [ 0.014486] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
    [ 0.014570] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
    [ 0.016276] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
    [ 0.016350] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
    [ 0.016417] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
    [ 0.016481] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
    [ 0.016543] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
    [ 0.016610] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
    [ 0.016674] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
    [ 0.016738] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
    [ 0.016800] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
    [ 0.016869] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
    [ 0.016934] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
    [ 0.016998] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
    [ 0.017061] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
    [ 0.017142] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
    [ 0.017445] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
    [ 0.017677] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
    [ 0.022012] bio: create slab <bio-0> at 0
    [ 0.022320] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
    [ 0.022346] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
    [ 0.022374] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
    [ 0.022386] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
    [ 0.022731] SCSI subsystem initialized
    [ 0.022941] usbcore: registered new interface driver usbfs
    [ 0.022971] usbcore: registered new interface driver hub
    [ 0.023029] usbcore: registered new device driver usb
    [ 0.023048] media: Linux media interface: v0.10
    [ 0.023073] Linux video capture interface: v2.00
    [ 0.023111] pps_core: LinuxPPS API ver. 1 registered
    [ 0.023115] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [ 0.023125] PTP clock support registered
    [ 0.023355] Advanced Linux Sound Architecture Driver Initialized.
    [ 0.023638] Bluetooth: Core ver 2.18
    [ 0.023651] NET: Registered protocol family 31
    [ 0.023654] Bluetooth: HCI device and connection manager initialized
    [ 0.023663] Bluetooth: HCI socket layer initialized
    [ 0.023670] Bluetooth: L2CAP socket layer initialized
    [ 0.023676] Bluetooth: SCO socket layer initialized
    [ 0.024073] Switched to clocksource arch_sys_counter
    [ 0.024085] cfg80211: Calling CRDA to update world regulatory domain
    [ 0.028430] thermal thermal_zone0: failed to read out thermal zone 0
    [ 0.028517] NET: Registered protocol family 2
    [ 0.028916] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.028932] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    [ 0.028953] TCP: Hash tables configured (established 2048 bind 2048)
    [ 0.028987] TCP: reno registered
    [ 0.028993] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.029004] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.029140] NET: Registered protocol family 1
    [ 0.029362] RPC: Registered named UNIX socket transport module.
    [ 0.029368] RPC: Registered udp transport module.
    [ 0.029371] RPC: Registered tcp transport module.
    [ 0.029374] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.029976] futex hash table entries: 512 (order: 3, 32768 bytes)
    [ 0.030320] bounce pool size: 64 pages
    [ 0.030847] NFS: Registering the id_resolver key type
    [ 0.030873] Key type id_resolver registered
    [ 0.030877] Key type id_legacy registered
    [ 0.030888] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    [ 0.031024] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
    [ 0.031341] msgmni has been set to 462
    [ 0.032094] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
    [ 0.032101] io scheduler noop registered
    [ 0.032118] io scheduler cfq registered (default)
    [ 0.032339] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
    [ 0.032622] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
    [ 0.098358] brcmstb_memc f1102000.memc-ddr: registered
    [ 0.098383] brcmstb_memc f1182000.memc-ddr: registered
    [ 0.098578] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.099394] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
    [ 0.196020] console [ttyS0] enabled
    [ 0.197274] loop: module loaded
    [ 0.197919] ahci brcmstb-ahci.0: can't get clock
    [ 0.198539] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
    [ 0.210088] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
    [ 0.211083] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
    [ 0.213724] scsi0 : ahci_platform
    [ 0.214357] scsi1 : ahci_platform
    [ 0.214861] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
    [ 0.215778] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
    [ 0.217212] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
    [ 0.217978] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
    [ 0.219122] m25p80 spi32766.0: found mx25l25635e, expected m25p80
    [ 0.219828] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
    [ 0.220562] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
    [ 0.221210] 5 ofpart partitions found on MTD device spi32766.0
    [ 0.221880] Creating 5 MTD partitions on "spi32766.0":
    [ 0.222479] 0x000000000000-0x000000200000 : "flash0.bolt"
    [ 0.223580] 0x000000200000-0x000000220000 : "flash0.nvram"
    [ 0.224620] 0x000000220000-0x000000240000 : "flash0.devtree"
    [ 0.225678] 0x000000240000-0x000001000000 : "flash0.recovery"
    [ 0.226749] 0x000000000000-0x000002000000 : "flash0"
    [ 0.228023] libphy: Fixed MDIO Bus: probed
    [ 0.228626] tun: Universal TUN/TAP device driver, 1.6
    [ 0.229215] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [ 0.230253] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
    [ 0.244079] libphy: bcmgenet MII bus: probed
    [ 0.264956] xhci-brcm: xHCI BRCM driver
    [ 0.265479] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
    [ 0.266150] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
    [ 0.267331] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
    [ 0.268174] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.268953] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.269789] usb usb1: Product: xHCI Host Controller
    [ 0.270355] usb usb1: Manufacturer: Linux 3.14-1.17-dm900 xhci-hcd
    [ 0.271070] usb usb1: SerialNumber: f0471000.xhci_v2
    [ 0.271957] hub 1-0:1.0: USB hub found
    [ 0.272421] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
    [ 0.273352] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
    [ 0.274012] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
    [ 0.275033] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
    [ 0.275827] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.276666] usb usb2: Product: xHCI Host Controller
    [ 0.277235] usb usb2: Manufacturer: Linux 3.14-1.17-dm900 xhci-hcd
    [ 0.277944] usb usb2: SerialNumber: f0471000.xhci_v2
    [ 0.278789] hub 2-0:1.0: USB hub found
    [ 0.279250] hub 2-0:1.0: 2 ports detected
    [ 0.280018] ehci-brcm: EHCI BRCM driver
    [ 0.280546] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
    [ 0.281214] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
    [ 0.292228] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
    [ 0.298084] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
    [ 0.298891] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.299679] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.300513] usb usb3: Product: EHCI Host Controller
    [ 0.301081] usb usb3: Manufacturer: Linux 3.14-1.17-dm900 ehci_hcd
    [ 0.301790] usb usb3: SerialNumber: f0470300.ehci_v2
    [ 0.302637] hub 3-0:1.0: USB hub found
    [ 0.303096] hub 3-0:1.0: 1 port detected
    [ 0.303734] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
    [ 0.304403] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
    [ 0.315397] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
    [ 0.322081] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
    [ 0.322884] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.323672] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.324506] usb usb4: Product: EHCI Host Controller
    [ 0.325073] usb usb4: Manufacturer: Linux 3.14-1.17-dm900 ehci_hcd
    [ 0.325782] usb usb4: SerialNumber: f0470500.ehci_v2
    [ 0.326091] ata1: SATA link down (SStatus 0 SControl 300)
    [ 0.327245] hub 4-0:1.0: USB hub found
    [ 0.327698] hub 4-0:1.0: 1 port detected
    [ 0.328397] ohci-brcm: OHCI BRCM driver
    [ 0.328891] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
    [ 0.329564] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
    [ 0.330488] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
    [ 0.386191] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
    [ 0.386971] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.387806] usb usb5: Product: BRCM OHCI controller
    [ 0.388374] usb usb5: Manufacturer: Linux 3.14-1.17-dm900 ohci_hcd
    [ 0.389089] usb usb5: SerialNumber: f0470400.ohci_v2
    [ 0.389938] hub 5-0:1.0: USB hub found
    [ 0.390414] hub 5-0:1.0: 1 port detected
    [ 0.391085] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
    [ 0.391748] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
    [ 0.392671] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
    [ 0.438082] ata2: SATA link down (SStatus 0 SControl 300)
    [ 0.448180] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
    [ 0.448960] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.449796] usb usb6: Product: BRCM OHCI controller
    [ 0.450363] usb usb6: Manufacturer: Linux 3.14-1.17-dm900 ohci_hcd
    [ 0.451079] usb usb6: SerialNumber: f0470600.ohci_v2
    [ 0.451906] hub 6-0:1.0: USB hub found
    [ 0.452375] hub 6-0:1.0: 1 port detected
    [ 0.453073] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.453823] ehci-pci: EHCI PCI platform driver
    [ 0.454380] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.455100] ohci-pci: OHCI PCI platform driver
    [ 0.455725] usbcore: registered new interface driver usb-storage
    [ 0.456428] i2c /dev entries driver
    [ 0.456883] lirc_dev: IR Remote Control driver registered, major 250
    [ 0.457927] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
    [ 0.458901] usbcore: registered new interface driver btusb
    [ 0.459594] cpufreq_cpu0: failed to get cpu0 regulator: -19
    [ 0.460410] brcmstb-cpufreq: probe of f03e257c.cpu-clk-div failed with error -17
    [ 0.461337] sdhci: Secure Digital Host Controller Interface driver
    [ 0.462044] sdhci: Copyright(c) Pierre Ossman
    [ 0.462552] sdhci-pltfm: SDHCI platform and OF driver helper
    [ 0.464305] mmc0: no vqmmc regulator found
    [ 0.464779] mmc0: no vmmc regulator found
    [ 0.495083] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
    [ 0.496991] mmc1: no vqmmc regulator found
    [ 0.497470] mmc1: no vmmc regulator found
    [ 0.528078] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
    [ 0.529023] hidraw: raw HID events driver (C) Jiri Kosina
    [ 0.529737] usbcore: registered new interface driver usbhid
    [ 0.530384] usbhid: USB HID core driver
    [ 0.532819] TCP: cubic registered
    [ 0.533820] NET: Registered protocol family 10
    [ 0.534813] NET: Registered protocol family 17
    [ 0.535564] Bluetooth: RFCOMM TTY layer initialized
    [ 0.536147] Bluetooth: RFCOMM socket layer initialized
    [ 0.536736] Bluetooth: RFCOMM ver 1.11
    [ 0.537176] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 0.537786] Bluetooth: BNEP filters: protocol multicast
    [ 0.538395] Bluetooth: BNEP socket layer initialized
    [ 0.538965] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [ 0.539654] Bluetooth: HIDP socket layer initialized
    [ 0.540275] l2tp_core: L2TP core driver, V2.0
    [ 0.540798] Key type dns_resolver registered
    [ 0.541367] Registering SWP/SWPB emulation handler
    [ 0.542192] regulator-dummy: disabling
    [ 0.542825] ALSA device list:
    [ 0.543189] No soundcards found.
    [ 0.543804] Waiting for root device /dev/mmcblk0p2...
    [ 0.595724] mmc1: BKOPS_EN bit is not set
    [ 0.602427] mmc1: new high speed MMC card at address 0001
    [ 0.603251] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
    [ 0.603854] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
    [ 0.604652] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
    [ 0.605413] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
    [ 0.609142] mmcblk0: p1 p2 p3
    [ 0.611681] mmcblk0boot1: unknown partition table
    [ 0.612711] mmcblk0boot0: unknown partition table
    [ 0.650269] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
    [ 0.651232] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
    [ 0.652435] devtmpfs: error mounting -2
    [ 0.652922] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
    [ 0.654425] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14-1.17-dm900 #1
    [ 0.655214] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x10/0x14)
    [ 0.656107] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c)
    [ 0.656939] [<c05d0408>] (dump_stack) from [<c05cf770>] (panic+0xa0/0x1f0)
    [ 0.657730] [<c05cf770>] (panic) from [<c05cd564>] (cpu_die+0x0/0x90)
    [ 0.658470] [<c05cd564>] (cpu_die) from [<00000000>] ( (null))
    [ 0.659157] CPU0: stopping
    [ 0.659473] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14-1.17-dm900 #1
    [ 0.660248] [<c0014eb0>] (unwind_backtrace) from [<c00112f0>] (show_stack+0x10/0x14)
    [ 0.661138] [<c00112f0>] (show_stack) from [<c05d0408>] (dump_stack+0x88/0x9c)
    [ 0.661968] [<c05d0408>] (dump_stack) from [<c00140d4>] (handle_IPI+0x164/0x198)
    [ 0.662818] [<c00140d4>] (handle_IPI) from [<c00085cc>] (gic_handle_irq+0x58/0x5c)
    [ 0.663688] [<c00085cc>] (gic_handle_irq) from [<c0011dc0>] (__irq_svc+0x40/0x50)
    [ 0.664546] Exception stack(0xc07cdf60 to 0xc07cdfa8)
    [ 0.665127] df60: ffffffed 0d7f8000 c07d54c8 00000000 c07cc030 c07d4420 c07d449c c05d788c
    [ 0.666065] df80: c0801961 c0801961 c07cc000 00000000 00000000 c07cdfa8 c000efb0 c000efa8
    [ 0.667000] dfa0: 60000113 ffffffff
    [ 0.667407] [<c0011dc0>] (__irq_svc) from [<c000efa8>] (arch_cpu_idle+0x2c/0x38)
    [ 0.668260] [<c000efa8>] (arch_cpu_idle) from [<c00638f8>] (cpu_startup_entry+0x100/0x144)
    [ 0.669214] [<c00638f8>] (cpu_startup_entry) from [<c078dbf0>] (start_kernel+0x414/0x420)

    PROBLEM NE OLABÝLÝR NE YPMAMIZ LAZIM?
    öndeki butonu gerekirse tekrar tekrar deneyerek recovery yazýlým yükleme
    moduna getirmeyi deneyin sabýrla dm525 de buna benzer sorun yaþadým ayrýca
    kurtardýktan sonra cihazýnýzý bu tür risklere karþý korumak adýna BARRYALLEN
    eklentisi kullanrak imajlarý makinaya deðil usb belleðe kurduðunuzda
    rahat rahat kurcalayýp istedðiniz imajlarý korkmadan kurup deneyebilirsiniz..

    bu videolarý dikkaklice izleyin..

    [Deðerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanýz gerekiyorÜye olmak icin burayý týklayýnýz]


    [Deðerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanýz gerekiyorÜye olmak icin burayý týklayýnýz]


    [Deðerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanýz gerekiyorÜye olmak icin burayý týklayýnýz]
    AlýntýAlýntý

  3. Teşekkür edenler:

    talhakrgzoglu (21.04.2018) , iyikosan (17.04.2018)

 

 

Benzer Konular

  1. Dreambox Kýrmýzý ýþýk (Kurtarma)
    Von obin im Forum Dreambox FAQ, Tarife
    Cevaplar: 64
    Son Mesaj: 30.12.2023, 22:32

Yetkileriniz

  • Konu Acma Yetkiniz Yok
  • Cevap Yazma Yetkiniz Yok
  • Eklenti Yükleme Yetkiniz Yok
  • Mesajýnýzý Deðiþtirme Yetkiniz Yok
  •  

Page generated in 1.711.721.178.55416 seconds with 17 queries Sayfa Boyutu (269249)