İyi çalışma ustad,eline sağlık.
ClarkConect5.0 amd işlemcili pc ye kurabilirmiyiz acaba.
İyi çalışma ustad,eline sağlık.
ClarkConect5.0 amd işlemcili pc ye kurabilirmiyiz acaba.
evet Calisirasef Nickli Üyeden Alıntı [Değerli Ziyaretci, linki görmeniz icin bu mesaja cevap yazmanız gerekiyorÜye olmak icin burayı tıklayınız]
Postun sağ alt kösedeki teşekkür (danke) butonuna basarsanız yeterli olur.
ne yaptıysam http ara birimi açılmadı clark connect 5.0 da
Ayrıca kurulumda vermiş olduğum root passwordu putty de ve winscp de kullanıyorum ama
clark connect kurduğum bilgisayarda açılışda çıkan ekranda kabul görmüyor.
yum komutu ile bahsedilen httpd kurulum işlemlerini yaptım,
güvenlik duvarını xp kurulu pc de kapadım kaspersky kaldırdım
3 ayrı browser (ie, opera , firefox)
2 ayrı pcde http arabirim açılmadı...
sertifika kabul ettim ama olmadı bir türlü olmadı
manuel http başlatma komutu verdim
http başlatılıyor diye mesaj düşüyor sonra tık yok
7 defa baştan kurdum cc 5.0
olmadı olmadı
bu konuyla ilgilide en mantıklı şu yazıyı buldum ama bi sonuç çıkmadı
Using ClarkConnect's Webconfig
If you've made it to this point, the hard part is behind you! Congratulations.. The ClarkConnect web-based interface is one of the simplest
User Interfaces available to manage a Linux-based server. A web-based User Interface - often referred to as 'webconfig' - allows you to
use any PC (running any operating system) on your LAN to configure and manage your server. By making adjustments in your firewall,
this functionality can be extended to a computer located anywhere on the planet, provided the user has been allowed access using a secret
username/password.
Webconfig listens for client requests on a non-standard port [port 81]. This means you'll need to add the port identifier in your browser.
In general, the URL that will provide you with initial access to the webconfig pages is:
Note the protocol uses HTTPS which means communication between the client and server uses 128bit encryption at all times. The use of
this protocol allows secure remote management or a server from a PC outside the LAN, however, when not being used, it is a good idea to
keep this port (81) closed.
The address or domain name comes after the protocol. In this example, 192.168.1.1 is the internal IP address of the ClarkConnect server.
You set-up may differ depending on what you entered in step 6 of the installation notes above. If you are using the DNS caching
nameserver, you can also use the server's domain name set in step 8 which is a little easier to remember.
Next in the URL is the port specifier. This isn't usually required in your day-to-day browsing of websites on the Internet, but because we
use a non-standard port, it must be provided. In this case, you will add “:81” to specify the request be made to port 81.
Finally, the folder location is specified. The administration area requiring 'root' privileges is located in the 'admin' directory.
Provided your PC is setup on the network correctly, enter the above URL (modified for your custom settings) into any client browser.
Next, your browser will pop-up an authentication dialog window requesting a username and password. Enter:
Username: root
Password: <your system password entered in step 9 of the installation notes above>
The system 'Dashboard' – an overview page – will be displayed similar to the screenshot on the following page. From this page, you will
see group headings along the top and a sub-menu displayed down the left hand navigation bar that will guide you through the various
configuration and reporting features of ClarkConnect.
problemi buldum kurulumda turkçe dil seçmekmiş
ingilizce seçince düzeldi
teşekkürler çook güzel bir açıklama gangster429 üstad yanlız takıldığım bir yer var serveri kurdum çook güzel çalışıyor ama elektirik gidip geldiğinde dns yi güncelleme işini beceremedim neden dersen ben no-ip kullanıyorum linux için client indirdim ama servere atamadım daha doğrusu nereye atacağımı bulamadım bunu tarif ederseniz çook memnun olurum.
yardımlar için şimdiden teşekkürler..
kardeş çok teşekürler verdiğin bilgiler için bende bir sorun oldu pc clarkconneck kurdum 4.3 başka pc flashfxp ile bağlandım cccam x86 dosyasını bindosyası adında klasör oluşturup var içine attım aynı şekilde cccam cfg. dosyasınıda etc diye kılasör oluşturup var içine atım cccam start ettim putty le kendi dreambox ma c line gönderdim örnek: pc f satırına şöyle yazdım F: onur 3388 2 2 0 0 { 0:0:2 } { } { } # dreamboxtaki c satırınada örnek c: 192.168.2.5 12000 onur 3388 no { 0:0:2 } buşekide yaptım pc takılı kartım çalışıyor dreambox tan seyrediyorum. sonun şu pc deki cfg dosyasına başkasından aldıgım c yi ekleyince çalışmıyor 1 kart görünüyor oda benim kart sebeb ne olabilir nerde hata yayapıyorum sorvır ayarıda şöyle SERIAL READER : /dev/ttyS0
TRY ALL CHIDS : /dev/ttyS0
#SMARTCARD CLOCK FREQUENCY:/dev/ttys0 6000000
SERIAL READER : /dev/ttyS1
TRY ALL CHIDS : /dev/ttyS1
#SMARTCARD CLOCK FREQUENCY:/dev/ttys1 6000000
SERVER LISTEN PORT : 12000
GLOBAL LIMITS : { 0:0:2 }
MINIMUM DOWNHOPS: 1
MINIMUM CLIENT VERSION : 2.0.4
EXTRA EMM LEVEL:yes
WEBINFO USERNAME : root
WEBINFO PASSWORD : dreambox
WEBINFO LISTEN PORT : 16001
Paylaş